arasmama
07-14-2005, 03:38 PM
For this one, I didn't want to have to handstitch and I wanted my design centered, so I changed the sewing a bit.
Finished product:
http://www.araspants.com/images/july14-1.jpg
First, fold your placemat so the side seams overlap 1/4" in the center.
http://www.araspants.com/images/pmpfold.jpg
Sew down this seam. You will have to do it in steps since the opening isn't wide enough for your sewing machine arm. The steps I did were:
starting at the top going as far as I could manage
http://www.araspants.com/images/pmpcenter.jpg
Then starting at 2/3 way down going back towards the seam I just ended:
http://www.araspants.com/images/pmpcenter1.jpg
I had to pull the purse inside out for that seam.
http://www.araspants.com/images/pmpcenter1-1.jpg
Then turn the bag around and start at the middle seam and sew towards the end.
http://www.araspants.com/images/pmpcenter2.jpg
Then iron (because it will be a wrinkled mess) and fold the bottom and top to make the purse.
http://www.araspants.com/images/pmpfoldpockets.jpg
I added magnetic snap closures next. You can do any closure you want though (or no closure).
http://www.araspants.com/images/pmpmagnetic.jpg
I wanted a chinese coin embellishment on the front, so I added that next.
http://www.araspants.com/images/pmpembellish.jpg
Next, you add the straps. I used cording. To keep from fraying, I taped where I was going to cut an then snipped in the middle of the tape.
http://www.araspants.com/images/pmptape.jpg
I then pinned it so it would lay between the layers.
http://www.araspants.com/images/pmpstrappin2.jpg
I pinned it to the inside pocket so the stitching would not show on the outside of the purse.
http://www.araspants.com/images/pmpstrappin.jpg
Next I zig zagged the strap in, to make sure it was extra secure.
http://www.araspants.com/images/pmpstrap.jpg
Then stitch up both side seams, going back and forth over the strap a few times.
http://www.araspants.com/images/pmpsideseam1.jpg
http://www.araspants.com/images/pmpsideseam.jpg
That is it! Your 20 minute purse is done.
Finished product:
http://www.araspants.com/images/july14-1.jpg
First, fold your placemat so the side seams overlap 1/4" in the center.
http://www.araspants.com/images/pmpfold.jpg
Sew down this seam. You will have to do it in steps since the opening isn't wide enough for your sewing machine arm. The steps I did were:
starting at the top going as far as I could manage
http://www.araspants.com/images/pmpcenter.jpg
Then starting at 2/3 way down going back towards the seam I just ended:
http://www.araspants.com/images/pmpcenter1.jpg
I had to pull the purse inside out for that seam.
http://www.araspants.com/images/pmpcenter1-1.jpg
Then turn the bag around and start at the middle seam and sew towards the end.
http://www.araspants.com/images/pmpcenter2.jpg
Then iron (because it will be a wrinkled mess) and fold the bottom and top to make the purse.
http://www.araspants.com/images/pmpfoldpockets.jpg
I added magnetic snap closures next. You can do any closure you want though (or no closure).
http://www.araspants.com/images/pmpmagnetic.jpg
I wanted a chinese coin embellishment on the front, so I added that next.
http://www.araspants.com/images/pmpembellish.jpg
Next, you add the straps. I used cording. To keep from fraying, I taped where I was going to cut an then snipped in the middle of the tape.
http://www.araspants.com/images/pmptape.jpg
I then pinned it so it would lay between the layers.
http://www.araspants.com/images/pmpstrappin2.jpg
I pinned it to the inside pocket so the stitching would not show on the outside of the purse.
http://www.araspants.com/images/pmpstrappin.jpg
Next I zig zagged the strap in, to make sure it was extra secure.
http://www.araspants.com/images/pmpstrap.jpg
Then stitch up both side seams, going back and forth over the strap a few times.
http://www.araspants.com/images/pmpsideseam1.jpg
http://www.araspants.com/images/pmpsideseam.jpg
That is it! Your 20 minute purse is done.