sandrahd
05-27-2012, 08:15 PM
Today, we’re going to finish putting together the base of the slipcover. This can be accomplished with 2 seams plus the addition of a skirt or ruffle. Let’s get started.
At this point, you should have the part of the slipcover you put together in part 1 and both armrest covers that you put together in part 2 on the chair, wrong sides facing out.
Pin the following seams. (You should basically be able to do this all as 1 seam that goes up the front side,
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1967.jpg
in front of the armrest, down the side under the seat cushion,
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1968.jpg
up the side of the back cushion,
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1969.jpg
over the top side of the back,
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1969.jpg
and down the back sides. )
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1970.jpg
You can either trim the seam allowances to ½-inch or use the pins you put in as your seam markings and sew along them. Either way, sew your seam(s). (You have a decision to make here. The slipcover made this way will be VERY form-fitting. It will be difficult to stretch on, but I’ve been able to do it. Your other option is to leave one of the seams that runs down the back open and attach ties or Velcro.)
Now, turn your slipcover right side out and put it on your chair. If you sewed both back seams (like I did), it may take some shimmying and rearranging to get it to fit.
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1971.jpg
Decide whether you want to do a straight skirt, a pleated skirt, or a ruffled skirt across the front. I decided to do a straight skirt with one big box pleat in the front. I reused the original hem from another side of my drop-cloth to make this easier to do. Cut a piece a little longer than the width you need by the length you will need plus seam allowance. Mark the center front if you want to put a pleat there.
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1972.jpg
Find the center of your ruffle and pin it in place. Pin the sides in place and then fashion your box pleat by bringing the excess to meet in the center front.
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1973.jpg
Go sew it on and bring your slipcover back to your chair and put it in place. (You won’t need to take it off again.)
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1974.jpg
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1975.jpg
If you have some wrinkles in the bottom of the chair, don’t sweat it. They will be covered up by your seat cushion.
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1976.jpg
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1977.jpg
Cool beans, huh?! :D
Tomorrow, we'll cover that ugly seat cushion!
At this point, you should have the part of the slipcover you put together in part 1 and both armrest covers that you put together in part 2 on the chair, wrong sides facing out.
Pin the following seams. (You should basically be able to do this all as 1 seam that goes up the front side,
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1967.jpg
in front of the armrest, down the side under the seat cushion,
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1968.jpg
up the side of the back cushion,
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1969.jpg
over the top side of the back,
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1969.jpg
and down the back sides. )
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1970.jpg
You can either trim the seam allowances to ½-inch or use the pins you put in as your seam markings and sew along them. Either way, sew your seam(s). (You have a decision to make here. The slipcover made this way will be VERY form-fitting. It will be difficult to stretch on, but I’ve been able to do it. Your other option is to leave one of the seams that runs down the back open and attach ties or Velcro.)
Now, turn your slipcover right side out and put it on your chair. If you sewed both back seams (like I did), it may take some shimmying and rearranging to get it to fit.
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1971.jpg
Decide whether you want to do a straight skirt, a pleated skirt, or a ruffled skirt across the front. I decided to do a straight skirt with one big box pleat in the front. I reused the original hem from another side of my drop-cloth to make this easier to do. Cut a piece a little longer than the width you need by the length you will need plus seam allowance. Mark the center front if you want to put a pleat there.
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1972.jpg
Find the center of your ruffle and pin it in place. Pin the sides in place and then fashion your box pleat by bringing the excess to meet in the center front.
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1973.jpg
Go sew it on and bring your slipcover back to your chair and put it in place. (You won’t need to take it off again.)
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1974.jpg
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1975.jpg
If you have some wrinkles in the bottom of the chair, don’t sweat it. They will be covered up by your seat cushion.
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1976.jpg
http://i248.photobucket.com/albums/gg177/sandrahd_photos/IMG_1977.jpg
Cool beans, huh?! :D
Tomorrow, we'll cover that ugly seat cushion!