SGRAHA
11-16-2010, 04:49 PM
I like making my own bias tape, that way i can have exactly what i want. I use a 1" bias tape maker, but the technique is the same no matter which one you use.
Step 1 - Get yourself a bias tape maker, you can buy them in Joann's, i found mine in the quilting section of notions (not the regular notions wall).
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step1-1.jpg
Step 2 - Cut a bunch of bias strips. For my 1" bias tape maker you cut 1 3/4" bias strips.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step2-1.jpg
Step 3 - Take your pile of strips to the sewing machine.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step3-1.jpg
Step 4 - Pin strips right sides together at a 90 degree angle (i actually don't pin i just hold them together).
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step4-1.jpg
Step 5 - Sew a 1/4" seam diagonally across the corner .
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step5-1.jpg
Step 6 - Press the seam out flat.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step6-1.jpg
Step 7 - Feed one end of your strip, wrong side up, into the bias tape maker. Use a pin to help guide it down through.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step7-1.jpg
Step 8 - Pull the end of the fabric slowly out and it will be folded in on itself.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step8-1.jpg
Step 9 - Now press well as you go, I use plenty of steam and just go slow so each part is pressed very well.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step9-1.jpg
Step 10 - Once you have your whole strip done from step 9, then press in 1/2 again to make your double fold. Again i press very well w/ lots of steam. VOILA you are done. I wrap it around a scrap piece of cardboard to keep it nice and flat.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step10-1.jpg
Step 1 - Get yourself a bias tape maker, you can buy them in Joann's, i found mine in the quilting section of notions (not the regular notions wall).
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step1-1.jpg
Step 2 - Cut a bunch of bias strips. For my 1" bias tape maker you cut 1 3/4" bias strips.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step2-1.jpg
Step 3 - Take your pile of strips to the sewing machine.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step3-1.jpg
Step 4 - Pin strips right sides together at a 90 degree angle (i actually don't pin i just hold them together).
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step4-1.jpg
Step 5 - Sew a 1/4" seam diagonally across the corner .
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step5-1.jpg
Step 6 - Press the seam out flat.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step6-1.jpg
Step 7 - Feed one end of your strip, wrong side up, into the bias tape maker. Use a pin to help guide it down through.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step7-1.jpg
Step 8 - Pull the end of the fabric slowly out and it will be folded in on itself.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step8-1.jpg
Step 9 - Now press well as you go, I use plenty of steam and just go slow so each part is pressed very well.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step9-1.jpg
Step 10 - Once you have your whole strip done from step 9, then press in 1/2 again to make your double fold. Again i press very well w/ lots of steam. VOILA you are done. I wrap it around a scrap piece of cardboard to keep it nice and flat.
http://i4.photobucket.com/albums/y109/SarahBethGraham/Step10-1.jpg